Notes On Chapter Nine -- Transmission Modes

• 9.1 Introduction
  
  
  • Ways data is transmitted
  • Serial and Parallel
  • Synchronous and Asynchronous
  
  
• 9.2 A Taxonomy of Transmission Modes
  
  
  • Serial transmission is sending one bit at a time
  • Parallel transmission is sending multiple bits at the same time over separate media
  • Taxonomy:
    • Parallel
    • Serial
      • Asynchronous
      • Synchronous
      • Isochronous
  
  
  
  
• 9.3 Parallel Transmission
  
  
  • The idea of parallel transmission: send 8 bits at exactly the same time, over 8 separate wires.
  • Besides the 8 data lines there are one or more control lines - wires to be used by sender and receiver to coordinate.
  • Advantages of parallel mode:
    • High speed
    • A good match to the underlying interface (computers use parallel circuitry internally. )
  
  
  
  
• 9.4 Serial Transmission
  
  
  • Most communication systems use serial mode because
    1. it is cheaper to extend single-wire systems to long distance, (fewer wires, simpler electronic components),
    2. parallel transmission is susceptible to timing problems cause by slight differences in length between data wires, and
    3. parallel communication lines generate noise at high data rates that interferes with signals in other nearby wires.
  • Universal Asynchronous Receiver and Transmitter (UART) or Universal Synchronous-Asynchronous Receiver and Transmitter (USART) chips may be used to convert between formats - the computer's internal parallel format and the serial format used for communication.
  
  
  
  
• 9.5 Transmission Order: Bits and Bytes
  
  
  • Sender and Receiver have to agree on such things as which byte of an integer will be transmitted first, and which bit of a byte is sent first.
  
  
  
  
• 9.6 Timing of Serial Transmission
  
  
  1. Asynchronous: This is transmission at any time, with arbitrary delay between transmission of any two successive data items.
  2. Synchronous: This is continuous transmission with no gaps between transmission of successive data items.
  3. Isochronous: This is transmission at regular intervals with a fixed gap between the transmission of successive data items.
  
  
• 9.7 Asynchronous Transmission
  
  
  • Asynchronous: the system allows the physical medium to be idle for an arbitrary time between successive data transmissions.
  • When transmitting data, usually the sender starts with extra bits called "start bits" or a "preamble" before sending the data. This allows the receiver to "synchronize with the signal."
  
  
• 9.8 RS-232 Asynchronous Character Transmission
  
  
  • RS-232 is a still widely used standard for sending characters asynchronously over a wire by transmitting bits serially, although USB is used instead of RS-232 in many applications.
    
    
  • According to RS-232, the sender holds the line low (-15 volts) when idle. There is a certain duration of time T for sending a bit. When starting to send a character, the sender holds the line high (at +15 volts) for time T. This "start bit" allows the receiver to detect that a character will be coming. Next the sender impresses each bit of the character on the line - time T each, with no spacing in between bits. Low means "1" and high means "0." After transmitting the last bit of the character, the sender brings the line low for at least time T (the "stop bit"), after which it may send another character when it wishes.
    
    
  
  
  
  
• 9.9 Synchronous Transmissions
  
  
  • Using synchronous transmission, a sender transmits bits continually with no idle time between successive bits.
  • Typically fewer "extra bits" are required - such as the the start and stop bits added to every character according to the RS-232 protocol.
  
  
  
  
• 9.10 Bytes, Blocks, and Frames
  
  
  • Typically synchronous systems send bytes in groups called frames.
  • To help sender and receiver stay synchronized, a frame starts with a special pattern of bits
  • Usually when the sender has no data to send, it transmits a special idle sequence
  
  
  
  
• 9.11 Isochronous Transmission
  
  
  • A way to use synchronous transmission to accept and send data at a fixed rate.
  • Applications: bit flow for multimedia containing voice, or video.
  
  
• 9.12 Simplex, Half-Duplex, and Full-Duplex Transmission
  
  
  • A simplex mechanism is capable of sending information in one direction only. A sender transmits on a simplex communication medium, but it cannot receive data on that medium. Simplex works kind-of like a one-way street.
  • Full duplex transmission allows simultaneous data flow in either direction between two points - kind-of like a two-way street.
  • Half-duplex allows communication in both directions, but not at the same time. The two sides have to take turns transmitting on the link. (Sometimes street or road traffic works like this when one lane of a two-way street has been closed for construction.) There has to be some sort of mechanism built into the protocol that makes sure only one side is transmitting at a time (collision avoidance).
  
  
  
  
• 9.13 DCE and DTE Equipment
  
  
  • To create a network connection, a business can lease a data circuit from a phone company.
  • The phone company attaches "Data Communications Equipment" (DCE) to the ends of the "leased line."
  • The business attaches "Data Terminal Equipment" (DTE) to the DCE.
  • RS-232, RS-449, and X.21 are among the protocols that may be used for communication between DCE and DTE.
  • The user can implement synchronous or isochronous transmission between the DCEs.