Notes On Chapter Ten -- Modulation and Modems

• 10.1 Introduction
  
  
  • How information is used to change a high-frequency electromagnetic wave, and
  • Why that is important
  
  
• 10.2 Carriers, Frequency and Propagation
  
  
  • Depending on the medium there will be certain frequencies that propagate better than others.
  • A common way of getting good performance is to place a continuously oscillating "carrier" electromagnetic wave on a medium - one that propagates well - and to transmit information by making small changes to the carrier.
  
  
• 10.3 Analog Modulation Schemes
  
  
  • The small changes made to the carrier are called "modulation"
  • Basically there are only three changes one can make to a wave:
    • Amplitude modulation (AM)
    • Frequency Modulation (FM)
    • Phase Shift Modulation
  
  
• 10.4 Amplitude Modulation
  
  
  • The amplitude of the carrier is varied in proportion to the signal being sent.
  • When AM is used to carry an analog signal, the "envelope" of the modulated wave has the shape of the signal.
  
  
• 10.5 Frequency Modulation
  
  
  • FM slightly increases the frequency of the carrier corresponding to where the signal is strong, and decreases it slightly corresponding to where the signal is weak.
  
  
• 10.6 Phase Shift Modulation
  
  
  • Phase shift modulation changes "the offset from a reference time at which the sine wave begins" i.e. it "slides" the waveform forward or backward slightly.
  • It is difficult to distinguish from FM in the case of an analog signal, so phase shift modulation is used on digital signals.
  
  
• 10.7 Amplitude Modulation and Shannon's Theorem
  
  
  • AM varies the amplitude only slightly.
  • Lowering the amplitude too much would also significantly lower the signal to noise ratio, which in turn could lead to lower effective bandwidth.
  • One might visualize the signal getting "lost in the noise."
  
  
• 10.8 Modulation,Digital Input and Shift Keying
  
  
  • When digital data is used to modulate a carrier, it is often called shift keying, instead of modulation.
  • There is a small fixed set of possible modulated values.
  • For example, with AM, there might be only the possible of running the carrier at full amplitude to represent a 1-bit, and at some significantly smaller amplitude to represent a 0-bit.
  
  
• 10.9 Phase Shift Keying
  
  
  • phase shift keying provides a convenient way to allow more than one bit to be sent during each period of the carrier.
  • For example, the four phase angles of -90, 0, 90 and 180 provide a two-bit code.
  
  
• 10.10 Phase Shift and a Constellation Diagram
  
  
  • Noise and distortion limit the ability of hardware to distinguish among minor differences in phase shifts.
  • Therefore it is not practical to use very many different phase shift keys.
  
  
• 10.11 Quadrature Amplitude Modulation
  
  
  • QAM schemes combines amplitude modulation and phase shift keying to achieve, for example the sending of a 4-bit codeword in each period of the carrier signal.
  
  
• 10.12 Modern Hardware for Modulation and Demodulation
  
  
  • A modulator is a device that accepts a stream of data bits and applies the corresponding modulation to a carrier wave (which causes the data to be transmitted on the carrier).
  • A demodulator is a device that inputs a modulated carrier signal and extracts from it the stream of data bits that was used to modulate the carrier. The demodulator outputs the data stream, so it can be used as input to another device.
  • Over a full-duplex communication channel using modulation and demodulation of a carrier, a modulator and demodulator are needed on both ends of the channel. Typically the two devices are combined into one unit - called a modem.
  
  
• 10.13 Optical and Radio Frequency Modems
  
  
  • There are RF modems to use with RF, and
  • Optical modems to use with optical fiber
  • The technology varies with the media, but the principle is the same.
  
  
• 10.14 Dialup Modems
  
  
  • A dialup modem modulates a (relatively low-frequency) analog audio carrier according to digital input it receives from, say, a computer.
  • Dialup modems can dial telephone numbers and answer incoming telephone calls. In other words they combine the functionality of a modem and a telephone.
  • When dialup modems were first designed, every stage of transmission of a telephone call was implemented utilizing modulated analog audio carrier technology.
  • Nowadays telephone companies use digital technology internally.
  • Calls that travel a long distance are digitized by telephone company equipment at a local telephone 'station' and transmitted to another station near the other party's telephone. That station translates the digital signal back into audio before relaying it to the other party.
  • So ironically, the digital info from a computer is translated by a modem into analog, and back into digital by the telephone company equipment. (Of course, the digital formats used by the computer and the telephone company are not compatible, so some kind of translation would be needed in any case.)
  • When a modem is part of the circuitry inside a computer it is called an internal modem. If it plugs in to the outside of a computer, it's an external modem
  
  
• 10.15 QAM Applied to Dialup
  
  
  • QAM is used with modern dialup modems to achieve higher bit rates.
  
  
• 10.16 V.32 and V.32bis Dialup Modems
  
  
  • The V.32 dialup modem standard uses 32 combinations of amplitude shift and phase shift to achieve a full-duplex data rate of 9600 bps.
  • The V.32bis standard employs 128 combinations of phase shift and amplitude shift, and achieves a data rate of 14,400 bps (also full-duplex).